DSMC2 Power Operations

This section describes the basic power operations for DSMC2 cameras.

DSMC2 Power Inputs

NOTE: The DSMC2 BRAINs themselves do not have DC IN power ports. A port expander or power module is required to power each camera.

The following devices have DC IN ports:

• DSMC2^® REDVOLT XL Module
• DSMC2 Base Expander
• DSMC2 V-Lock I/O Expander
• DSMC2 Jetpack Expander
• DSMC2 Jetpack-SDI Expander
• DSMC2 REDVOLT Expander
• DSMC2 V-Lock Battery Module
• DSMC2 Gold Mount Battery Module
• DSMC2 Production Module (V-Lock)
• DSMC2 Production Module (Gold Mount)

DSMC2 Power LEDs

This section describes the LED functions for the camera.

NOTE: When the camera is powered only by battery and not AC power, the Power Status LED (PWR) on the expander or module does not turn on. You can press the button on the battery to check the battery charge level.

DSMC2 Power Priority

When multiple power sources are connected to the camera, power consumption is prioritized in this sequence:

1. Any power supply connected to the DC IN port or the expander
2. Any power supply connected to the DC IN port on a rear battery module
3. Rear battery
4. REDVOLT battery in the DSMC2 REDVOLT Expander

DSMC2 Power Consumption

The DSMC2 cameras draw approximately 3.3 A (50 W) when configured with the DSMC2 Base Expander, DSMC2 RED Touch 7.0" LCD, and RED MINI-MAG 512GB.

Under typical conditions batteries provide the following operating time:

• REDVOLT: Powers the camera and accessories for approximately 30 minutes.
• REDVOLT-V: Powers the camera and accessories for approximately 35 minutes.
• REDVOLT XL: Powers the camera and accessories for approximately 90 minutes.
• RED BRICK: Powers the camera and accessories for approximately 120 minutes.

Approved DSMC2 External DC Power

The DSMC2 cameras accept input voltages of 11.5 V to 17 V DC, and can draw a maximum current of 9 A. The camera can be powered continuously by connecting one (1) of the following to an attached module or expander:

• DSMC AC Power Adaptor
• RED BRICK Charger: Offers two (2) ways to connect to your camera:
  • Use a RED ONE DC Power Cable (P/N 790-0060) and a 2B-to-1B Power Adaptor Cable (P/N 790-0138).
  • Use a RED 2B-to-1B Power Cable (P/N 790-0556, 790-0654).
• RED BRICK: Requires a DSMC2 V-Lock I/O Expander, Battery Belt Clip (DSMC), or DSMC2 V-Lock Battery Module. Also supported by a RED Quickplate or RED Cradle using a 2B-to-1B Power Adaptor Cable.
• REDVOLT-V: Requires a DSMC2 V-Lock I/O Expander, Battery Belt Clip (DSMC), or DSMC2 V-Lock Battery Module. Also supported by a RED Quickplate or RED Cradle using a 2B-to-1B Power Adaptor Cable.
• XLR DC power source: Requires an XLR Power Cable.

WARNING: While third-party batteries may be mechanically compatible with the camera system, the manufacturer is responsible for the performance and stability of third-party options, not RED. Damage to the camera system or third-party devices caused by using third-party power options is not covered under warranty. The camera may be unable to determine and display the voltage or remaining battery capacity of third-party power options.

Auto Boot on Power

The DSMC2 Jetpack Expander, DSMC2 Jetpack-SDI Expander, DSMC2 REDVOLT Expander, DSMC2 V-Lock I/O Expander, and DSMC2 Production Module feature a selector switch that enables the camera to automatically boot when power is provided via the DC IN connector on the expander. The Auto Boot on Power switch (identified by a line or a white star) is located on top of the device.

When Auto Boot on Power is enabled, the camera disables all power sources that are not the DC IN connector on the expander or module, including batteries and the DC IN connectors on any modules.

Enable Auto Boot on Power

1. Toggle the Auto Boot on Power switch to On (identified by a line or a white star).
2. Connect a power source to the DC IN connector.

   The camera turns on automatically.

3. Use one of the following methods to turn off the camera:

   • Go to Menu > Power and select Shutdown.

   • Press and hold PWR/REC until the Shutting Down... notification shows on the display.

     NOTE: Simply disconnecting the power source may result in data loss.

Disable Auto Boot on Power

1. Toggle the Auto Boot on Power switch to Off (identified by a circle or a black star).

   The camera will not turn on automatically.