REDVOLT XL Module
Figure: REDVOLT XL Module
The REDVOLT XL Module provides flexible mounting and power solutions for the EPIC/SCARLET. The reversible switch plate on the REDVOLT XL Module enables you to mount the module to the EPIC/SCARLET or another module. When the module is attached to the EPIC/SCARLET, a connected REDVOLT XL battery powers the system. Batteries can also be hot-swapped, as long as power is provided from a REDVOLT-equipped DSMC Side Handle or a DSMC AC Power Adaptor is connected to the DC IN port on the EPIC/SCARLET. The on-board 2-pin 0B AUX port provides a convenient 3.8 A power source for additional camera accessories.
A protective baseplate is included with the REDVOLT XL Module to serve as a portable and stand-alone battery charger. The module is capable of charging a REDVOLT XL battery while connected to the EPIC/SCARLET, as long as it is turned off.
WARNING: DO NOT attempt to power a third-party device without first verifying the cabling and connections are correct, since that may cause damage. Damage to the device, the module, or other components of the camera system caused by attempting to power a third-party device incorrectly may not be covered under warranty.
NOTE: The REDVOLT XL Module ONLY supports REDVOLT XL batteries. DO NOT use a REDVOLT battery.
NOTE: The REDVOLT XL Module requires that your camera is on firmware v5.1.29 or later.
REDVOLT XL Module Connections
Figure: REDVOLT XL Module
|
# |
Connector |
Connector Type |
Connector Function |
|---|---|---|---|
|
1 |
AUX POWER OUT - 3.8 A |
2-pin 0B |
Provides 3.8 A max current out for 2-pin based accessories when the module is receiving power |
|
2 |
CHARGE IN |
6-pin 1B |
Provides power to the REDVOLT XL Module, the AUX POWER OUT port, and an approximate 2 A charge current to an attached REDVOLT XL battery |
AUX POWER OUT
The 2-pin 0B AUX POWER OUT port provides a maximum 3.8 A of current for camera accessories.
NOTE: The AUX POWER OUT port is always active whenever a REDVOLT XL battery is attached to the module, regardless of camera state or presence of a DC power source.
Figure: Front Face of AUX POWER OUT Connector
|
2-Pin 0B AUX POWER OUT Connector |
|||
|---|---|---|---|
|
Pin |
Signal |
Description |
Direction |
|
1 |
GROUND |
Common ground |
N/A |
|
2 |
+11.5 to +17 VDC |
+11.5 to 17 VDC unregulated battery pass-through power |
Out |
NOTE: Mating connector is EEG.0B.302.CLL.
CHARGE IN
Use the 6-pin 1B CHARGE IN port to charge batteries and provide power to the AUX POWER OUT port.
Figure: Front Face of CHARGE IN Connector
|
6-pin 1B CHARGE IN Connector |
|||
|---|---|---|---|
|
Pin |
Signal |
Description |
Direction |
|
1 |
+VBATT |
Power input, +11.5 to +17 VDC |
Out |
|
2 |
+VBATT |
Power input, +11.5 to +17 VDC |
Out |
|
3 |
SCL-BATT |
Serial battery bus clock |
Out |
|
4 |
GROUND |
Power return (camera ground) |
Out |
|
5 |
GROUND |
Power return (camera ground) |
Out |
|
6 |
SDA-BATT |
Serial battery bus clock |
Out |
NOTE: Mating connector is FGJ.1B.306.CWLD72Z.
Compatible Cables
- 790-0138: RED 2B-to-1B Power Adaptor Cable
- 790-0164, 790-0646: XLR Power Cable (10')
- 790-0165, 790-0647: XLR Power Cable (30')
REDVOLT XL Module Indicator LEDs
The REDVOLT XL Module indicator LEDs display information about the current state of an equipped REDVOLT XL Battery when the module is used as a desktop charging station. Refer to the following table for information about the different REDVOLT XL charging states.
|
Color/Flashing |
Description |
|---|---|
|
Green |
Battery is fully charged |
|
Green flashing |
Charging; half second on, half second off |
|
Green/Red flashing |
Lamp self test at power up; half second red, half second green |
|
Green/Red flashing (alternating) |
Error; alternating, half second green, half second red, repeat |
|
Red flashing |
Battery discharge alert; heartbeat (red) pulse once per minute indicates that the battery is discharging and should be removed from module1 |
- The REDVOLT XL Module draws a small amount of power any time a battery is attached, when there is no charging source available.
Charge With the REDVOLT XL Module
Figure: REDVOLT XL Module Front (Left), and Rear (Right)
The REDVOLT XL Module charges one (1) REDVOLT XL battery when a DSMC AC Power Adaptor is connected to the 6-pin 1B CHARGE IN connector. The REDVOLT XL Module can fully charge a discharged REDVOLT XL battery in approximately four (4) hours.
The REDVOLT XL Module can charge a REDVOLT XL battery while attached to the camera, but only when the camera is off. When the camera is on, power is drawn from the battery rather than the attached power supply, resulting in a net loss of power. Connect a power source to the 6-pin 1B CHARGE IN port to provide power to the AUX POWER OUT port for additional camera accessories.
To charge a REDVOLT XL battery with the REDVOLT XL Module, follow the instructions below:
- Attach the protective baseplate to the REDVOLT XL Module.
- Connect the 6-pin 1B connector from a DSMC AC Power Adaptor to the CHARGE IN port.
- Insert a REDVOLT XL battery into the REDVOLT XL Module.
WARNING: DO NOT use the REDVOLT XL Module as a desktop charger without the protective baseplate to cover the rear connectors. This may cause irreparable damage to the rear connectors on the module and is not covered under warranty.
Install the REDVOLT XL Module
The REDVOLT XL Module is designed with a reversible switch plate, enabling direct installation to the EPIC/SCARLET BRAIN or mounting to other modules.
For more information on installing and removing the REDVOLT XL Module, go to:
REDVOLT XL Module SWITCH PLATE
Figure: REDVOLT XL Module Switch Plate
To configure the switch plate for different mounting variations, follow the instructions below:
- Loosen the six (6) M3x0.5 x 8 mm screws attaching the SWITCH PLATE evenly using a T10 TORX driver.
- Remove the six (6) screws. DO NOT discard screws.
- Install the switch plate to the desired mounting configuration:
- 4-BOLT-PLATE (Left image): Supports attachment directly to the BRAIN.
- MODULE PLATE (Right Image): Supports attachment to DSMC modules.
- Insert and tighten the six (6) M3x0.5 x 8 mm screws evenly. DO NOT FULLY TIGHTEN.
- Fully tighten the six (6) M3x0.5 x 8 mm screws evenly. DO NOT exceed 70 in-oz, or damage may occur.
WARNING: DO NOT OVERTIGHTEN.
NOTE: For more information or replacement screws, contact a Sales Representative.
Insert a REDVOLT XL
- Align and insert the REDVOLT XL.
- Apply pressure to the battery until a click is heard, signaling the battery is properly seated.
Figure: Insert a REDVOLT XL Battery
Remove a REDVOLT XL
-
Press the battery release buttons on both sides of the REDVOLT XL Module.
- Remove the REDVOLT XL.
Figure: Remove a REDVOLT XL Battery